Das SDM-SIO4A bietet zusätzliche serielle Eingänge für einen Datenlogger von Campbell Scientific, vier individuell konfigurierbare und adressierbare RS232, RS422 oder RS485 (Halb- oder Vollduplex)Ports zum Anschluss von intelligenten Sensoren, Dispalys uws. Der Logger muss SDM-fähig sein, dann können bis zu 3 Module an einem SDM-Port angeschlossen werden. Sie verhalten sich wie eingebaute serielle Ports und verwenden dieselben Programminstruktionen.
Das SDM-SIO4A ist am seriellen Eingang gegen Überspanung und Störsignale geschützt nach IEC61000-4-5 Level 4, so dass in den meisten Fällen kein zusätzlicher Überspannugnsschutz notwendig ist.
Hinweis: Das SDM-SIO4A ist kein direkter Ersatz für das SDM-SIO4. Das SDM-SIO4A besteht aus 4 SDM-SIO1A Modulen in einem Gerät. Daher ist das SDM-SIO4A ein Ersatz für bis zu 4 SDM-SIO1 Module oder als Alternative zum SDM-SIO1A, wenn 4 zusätzliche Kanäle gebraucht werden.
Lesen Sie mehrThe SDM-SIO4A connects to multiple remote serial devices using industry-standard hardware that can be set to true RS-232, RS-485, or RS-422 signal levels. When operating in RS-232 mode, the channel also supports hardware handshaking. RS-422 mode is functionally the same as RS-485 mode, except the connection is limited to a point-to-point system. Connections and programming for RS-422 are otherwise identical to RS-485.
The SDM-SIO4A will accept serial data up to 6143 bytes and store it in its buffer. This allows remote equipment to transmit large amounts of data without needing to stop other processes in the datalogger.
Up to 3 SDM-SIO4A modules can be connected to a single datalogger using the SDM port, allowing a user to connect 12 different serial devices to a datalogger with ease. This is in addition to any connections made to the dataloggers via other serial ports.
Function | Expands the number of serial devices that can communicate with a data logger. |
Number of Channels | 4 |
Supported Data Rates | 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200 bits/s |
Supported Modes of Operation |
|
Supported Data Format |
|
Auto Baud Rate Detection | Auto baud rate detection is NOT supported. |
PakBus Communications | Use of the serial port for general PakBus communications is not currently supported. |
Voltage |
|
Operating Temperature | -40° to +70°C (standard) |
Humidity | 0% to 95% (non-condensing) standard |
Mounting Holes | Two spaced 17.78 cm (7 in.) apart |
Mounting Clips | Optional DIN rail mounting clips are available, which can be fitted to the base of the case. |
EMC Compliance | The SDM-SIO4A has been tested and shown to comply with IEC 61326. The device incorporates transient and surge protection that is designed to meet IEC61000-4-5, level 4, providing the device is adequately grounded. |
Dimensions | 6.4 x 15.45 x 2.2 cm (2.51 x 6.09 x 0.86 in.) excluding mounting tabs |
Buffer Sizes |
|
-NOTE- | Both transmit and receive buffers are fill and discard type. That is, after the buffers become full, no new information is accepted, and all further data is discarded until space is made when the data logger requests data from the SDM-SIO4A. |
Transmit Buffer Size | 767 bytes (buffer from the data logger to the sensor) |
Receive Buffer Size | 6143 bytes (buffer from the sensor to the data logger) |
Current Consumption |
|
Active Current | 9.6 to 11.7 mA (depending on transmit mode and connections made) |
Standby Current |
|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Product | Compatible | Note |
---|---|---|
CR1000 (retired) | ||
CR1000X | ||
CR200X (retired) | ||
CR216X (retired) | ||
CR300 (retired) | ||
CR3000 | On the CR3000, SDMs are connected to the ports labeled SDM-C1, SDM-C2, and SDM-C3. | |
CR310 | ||
CR350 | ||
CR5000 (retired) | The CR5000 is compatible with the SDM-SIO4A, but the operating system must be OS 6 or higher. On the CR5000, SDMs are connected to the ports labeled SDM-C1, SDM-C2, and SDM-C3. | |
CR6 | ||
CR800 (retired) | ||
CR850 (retired) | ||
CR9000X (retired) | The CR9000X's operating system must be OS 6 or higher. |
The SDM-SIO4A does NOT support auto baud rate detection nor the use of the serial port for general PakBus communications.
CR200(X) Series | CR800/CR850 | CR1000 | CR3000 | CR7X | CR9000X | CR6 | CR300 Series |
* | † |
Note:
*On the CR3000, SDMs are connected to the ports labeled SDM-C1, SDM-C2, and SDM-C3.
†The CR9000X's operating system must be OS 6 or higher.
The CR5000 is compatible with the SDM-SIO4A, but the operating system must be OS 6 or higher. On the CR5000, SDMs are connected to the ports labeled SDM-C1, SDM-C2, and SDM-C3.
None of our Edlog dataloggers are compatible with the SDM-SIO4A.
The SDM-SIO4A requires a desiccated, non-condensing environment; a Campbell Scientific enclosure is recommended. The SDM-SIO4A has built-in keyhole flanges for mounting to the backplates of Campbell Scientific enclosures.
ENC10/12 | ENC10/12R | ENC12/14 | ENC14/16 | ENC16/18 |
Current firmware for the SDM-SIO1A and SDM-SIO4A.