Überblick
Die 52202 ist eine elektrisch beheizbare Regenkippwaage die Regen, Schnee und anderen Niederschlag misst. Sie hat eine Auffangfläche von 200 cm2 und eine Auflösung von 0.1 mm und entspricht damtit den Vorgaben der WMO. Diese Regenkippwaage ist mit allen Campbell-Loggern kompatibel und wird in verschiedenen Anwendungen eingesetzt, Voraussetzung ist nur genügend Strom.
Lesen Sie mehrFunktionen und Vorteile
- High precision—tips at 0.1-mm increments
- Heating element melts snow and ice for year-round measurements
- Compatible with many Campbell Scientific data loggers
Bilder
Zugehörige Produkte
Technische Beschreibung
The 52202 funnels precipitation into a bucket mechanism that tips when filled to the calibrated level. Each tip is marked by a magnetic reed switch closure that is recorded by a Campbell Scientific datalogger pulse count channel.
The 52202 has an internal heater that melts snow or other frozen precipitation. This heater is thermostat controlled and requires a reliable source of 24 Vac power. A wall transformer is shipped with the 52202 that plugs into a wall socket to provide the required 24 Vac power.
Spezifikationen
| Sensor Type | Tipping bucket with magnetic reed switch (normally open) |
| Accuracy |
|
| Rainfall per Tip | 0.1 mm (0.004 in.) |
| Operating Temperature Range | -20° to +50°C (heated) |
| Humidity Range | 0 to 100% |
| Power | 18 W @ 24 Vac (for heater only) |
| Heater Thermostat Set Point | 10°C ±3°C |
| Contact Rating | 24 Vac/dc (400 mA maximum) |
| Compliance with Standards |
|
| Mounting Pipe | 30.5 cm (12 in.) length; 1 inch IPS, aluminum, unthreaded |
| Catchment Area | 200 cm2 (31 in.2) |
| Orifice Diameter | 16 cm (6.3 in.) |
| Diameter | 18.5 cm (7.3 in.) |
| Height | 30 cm (11.8 in.) |
| Power Plug Weight | 0.43 kg (0.95 lb) |
| Weight | 1.16 kg (2.55 lb) |
Kompatibel mit
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Datenlogger
| Product | Compatible | Note |
|---|---|---|
| CR1000 (retired) | ||
| CR1000X | ||
| CR300 (retired) | ||
| CR3000 | ||
| CR310 | ||
| CR350 | ||
| CR6 | ||
| CR800 (retired) | ||
| CR850 (retired) |
Additional Compatibility Information
Mounting
The 52202 is shipped with a mounting pipe. The rain gage clamps onto this pipe, which is then fastened to a crossarm using the CM220 Right-Angle Mounting Kit, or mounted onto the top of a tripod using the CM216 Sensor Mounting Kit.
Wind Screen
Campbell Scientific offers the 260-953 Wind Screen to help minimize the affect of wind on the rain measurements. This wind screen consists of 32 leaves that hang freely and swing as the wind moves past them.
Dokumente
Broschüren Produkte
Handbücher
Realisierte Projekte
FAQs für
Number of FAQs related to 52202-L: 10
Alle anzeigenWenige anzeigen
-
Follow the steps listed in the “Troubleshooting” section of the 52202-L Instruction Manual.
-
The 52202-L uses a reed switch to generate a pulse for each tip of the collector.
-
These rain gages can be connected to either.
- When a control port is used, one lead goes to the 5 V port to provide current, and the other lead goes to a control port to detect the current.
- When a pulse channel is used, one lead goes to the pulse port, and the other lead terminates on a ground terminal.
-
No. The relay that controls power to the heater uses ac power only.
-
Not registering any tips, missing tips, or double tips.
-
If data is not being logged correctly, there are two likely causes:
- The reed switch has failed.
- There is a faulty connection from the rain gage to the data logger, typically caused by a broken conductor or corroded wiring.
-
Not enough tips or too many tips.
-
The 260-953 Alter-type rain gage wind screen consists of 32 heavy metal leaves that hang freely and swing as the wind moves past them. The swinging leaves act as a wind damper and help minimize the effect of wind on the rain measurements without adding additional turbulence.
-
The most common errors are either that the rain gage appears to have drifted out of calibration or that the tips are not being correctly recorded by the data logger.
-
When a rain gage is out of calibration, it is usually because of the buildup of dirt and grime on the internal surfaces of the tipping bucket mechanism. Cleaning the internal surfaces usually brings the rain gage back into calibration. It is also possible that a rain gage is out of calibration because it is no longer level.
To minimize the possible occurrence of calibration errors, perform routine cleaning and maintenance of the rain gage at least once every three months. The environmental conditions at a particular site may require a facility to perform cleaning, leveling, and maintenance on a much more frequent schedule.
Anwendungsbeispiele
Pont del Petroli was built in the 1960s to enable the transfer of oil from......lesen Sie mehr