Bild nicht verfügbar
problemloser Langzeitschutz für Ihren Logger
Überblick
Das FC100 ist zur Verwendung mit dem SG000 Strike guard Blitzwarnsystem entwickelt worden. Das SG000 gibt ein Signal über Lasfaserkabel aus. Das FC100 ist am Ende des Kabels angebracht und vor dem Datenlogger. Es konvertiert das Signal zu einem RS232 Signal zu blitzgeschützten Verbindung von Sensor und Logger.
Das FC100 kann auch als RS232-Verbindung zwischen zwei seriellen Geräten (Logger und PC) dienen, die weniger als 100m auseinander stehen. Es ist ein DCE Gerät, so dass ein Nullmodemkabel zur Verbindung mit dem Logger benutzt werden muss.
Lesen Sie mehrFunktionen und Vorteile
- Blitzgeschützte und blitzsichere serielle Kommunikation
- Robustes Design für langen problemlosen Betrieb
- ohne Stecker, crimpen, schleifen oder Epoxy
Technische Beschreibung
The FC100 is designed for use with the SG000 Strike Guard lightning detector as part of the CS110 lightning warning system. The SG000 outputs its data signal via fiber-optic cable, and the FC100 is installed at the end of the fiber-optic cable and before the datalogger. The FC100 converts a fiber-optic data signal into an RS-232 signal for a lightning-proof connection between the sensor and the datalogger.
The FC100 can also be used as an RS-232 link between two serial devices (datalogger to PC) separated by less than 328 ft (100 m). The FC100 is a DCE device so a null modem cable will be needed between it and a datalogger.
Spezifikationen
| Electrical Connector | 9-pin, D sub, DTE compatible |
| Baud Rates | 1,200 to 19,200 bps (at 100 m guaranteed with FC100CBL-L cable) |
| Power | 12 Vdc (via pn 14291 or pn 15966) |
| Current | 5 mA (average) |
| Mounting Holes | 7.62 cm (3 in.) apart |
| Case Width | 2.8 cm (1.1 in.) |
| Dimensions |
|
Kompatibel mit
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Datenlogger
| Product | Compatible | Note |
|---|---|---|
| CR1000 (retired) | ||
| CR1000X | ||
| CR200X (retired) | ||
| CR216X (retired) | ||
| CR300 (retired) | ||
| CR3000 | ||
| CR310 | ||
| CR350 | ||
| CR5000 (retired) | ||
| CR6 | ||
| CR800 (retired) | ||
| CR850 (retired) | ||
| CR9000X (retired) |
Additional Compatibility Information
The FC100 is used with the SG000 Strike Guard.
FAQs für
Number of FAQs related to FC100: 10
Alle anzeigenWenige anzeigen
-
Short-fiber runs sometimes pass too much signal. The solution is to pull the fiber part way out of the holding ferrule.
-
With a good signal strength, 1200 to 19,200 bps.
-
The FC100 provides instant termination—no connectors, crimping, polishing, or epoxy.
-
The 12 Vdc power supply keeps the signal from dropping when large data packets are transmitted.
-
The data transmission fibers are fragile and cannot be bent or broken. Consequently, the fibers need to be handled with care and protected inside a conduit (usually PVC).
-
They provide lightning-proof and lightning-safe serial communication that eliminates the need for transient suppression devices.
-
100 m (330 ft) with a 1.0 mm poly-methylmethacrylate (PMMA) core with a PVC or polyethylene jacket, simplex or duplex; up to 1 km with a higher-grade fiber.
-
Direct communication between two RS-232 serial devices, such as a PC to a datalogger or a datalogger to a serial sensor.
-
The FC100 is designed for lightning-proof and lightning-safe serial communication. Because the FC100 offers PMMA or glass fibers that are not conductive, electrical surges (such as those caused by lightning) cannot travel between the modems.
-
The FC100 is required to communicate with the SG000 Strike Guard Lightning Sensor. The SG000 is an option for the CS110 Electric Field Sensor and the LW110 Lightning Warning System.